Hall Magnetic and Current Sensors

MV2-QFN with 3 arrows

Metrolab MagVector™ MV2 Digital 3-axis Hall Magnetic Sensor

The MagVector™ MV2 is the ideal solution if you need to integrate a sophisticated magnetometer into your electronic system.

  • Axis: 3-axis (Bx, By, Bz)
  • Selectable measurement ranges: from 100 mT to 30 T
  • Low noise: 300 nT/√Hz
  • Analog and digital interfaces
  • Selectable measurement rate: up to 3 kHz
Out of Stock

FAMAS – Magnetic Angle Sensor SENA2Dx

SENA2Dx is an integrated magnetic field sensor that allows the measurement of the rotation angle of the in-plane components of a magnetic field.

  • Contactless angle sensor 0–360°
  • Hall-based principle with patented direct angle-to-digital conversion
  • High magnetic fields of more than 500 mT do not cause damage to the sensor
Out of Stock

Senis 3DHALL – 3-Axis Hall Magnetic Sensor SENM3Dx

SENM3Dx is a CMOS integrated magnetic field sensor that allows the acquisition of all 3 magnetic-field components (Bx, By and Bz) at the same time and at the same spot.

  • Selection of active sensitivity axis 1D, 2D or 3D
  • High Magnetic resolution: 1uT
  • High spatial resolution: 100um x 100um for 3-axis
Out of Stock
Hall Element

AKM Hall Element Magnetic Sensors

AKM (Asahi Kasei) Hall Elements generate an output analog signal proportional to the intensity of the magnetic field.

  • Axis: 1-axis
  • HG Series, Excellent thermal characteristic. High linear output. Best suited to current sensors.
  • HQ Series, High sensitivity and low current consump­tion are achieved simulta­neously.
Out of Stock
Hall ICs

AKM Hall Magnetic Switch ICs

Detects a magnetic field and outputs a digital signal.

  • Unipolar Switch, On/off is switched depending on the intensity of the magnetic field of the S-pole of the magnet. This type is primarily used for position detection of a magnet.
  • Omnipolar Switch, On/Off is switched depending on the intensity of the magnetic field.
Out of Stock
AKM linear Hall IC

AKM Linear Hall Magnetic ICs

AKM (Asahi Kasei) Linear Hall Effect ICs generate an amplified analog signal proportional to the intensity of the magnetic field.

  • Axis: 1-axis (perpendicular to IC)
  • Sensitivity: ± 130mV/mT, ± 65mV/mT, ± 40mV/mT or ± 20mV/mT
  • Bandwidth: DC to 100kHz
  • Can be used in Open-loop Gapped Core Current Sensors
Out of Stock

AKM Currentier CQ / CZ Isolated Current Sensors

PCB Mount, Analog Signal Output, Open-Loop Current Sensors with Voltage Isolation to 3kV.

AKM Current Sensors utilize an array of extremely low noise Hall elements, rather than integrated Silicon Hall elements, to sense the magnetic field from the primary current with lower noise and much improved signal/noise performance.

Out of Stock
CS-03 Sensor

Senis CS-03 High Sensitivity Isolated Current Sensor

Senis CS-03 Low Current Sensor is a next-generation analog current sensor for bipolar current sensing.

  • Ranges: ±0.1A, ±0.2A, ±2A and ±8A
  • Accuracy: <2% of FS
  • Linearity: 0.5% (typical)
  • Bandwidth: DC to 5kHz
Out of Stock

Senis BBM-03-LV Series – Low/Medium Bus Bar Current Sensor

Bus Bar current sensor modules enable measurement of currents in the large f-bandwidth of DC to 200kHz without an impact of external magnetic fields.

  • Very compact, low profile package
  • Custom design bus bar geometries possible
  • Single +5V Power Supply at less than 25mA
Out of Stock

AKM EM-3242 Non-contact Magnetic Angle Sensor – Discontinued

AKM (Asahi Kesai) EM-3242 Non-contact, Absolute Angle Sensor IC Integrates a Hall element and processing IC into a single package.

  • Resolution: up to 10 bits (0.36°)
  • Non-linearity: 1%
  • Package: 6-SOP
Out of Stock

AKM AK877x Magnetic Encoder ICs – Discontinued

AKM (Asahi Kesai) AK-877x Magnetic provides digital outputs corresponding to the direction and number of poles from a rotating magnet.

  • Sensitivity: ±1.5mT to ±2mT
  • Frequency Response: to 8kHz
  • Outputs: Two Quadrature 90° Phased Outputs or Pulse Count and Direction of Rotation
Out of Stock